A two pack, acrylic polyurethane finish giving excellent durability and long term recoatability.
PRODUCT INFORMATION Color - PHB000-White, PHY999-Black ; and a wide range of colors. Finish/Sheen - High Gloss Part B (Curing Agent) - PHA046 Volume Solids - 57% ±3% (ISO 3233:1998) Mix Ratio - 6.00 volume(s) Part A to 1 volume(s) Part B Typical Film Thickness - 2 mils dry (3.5 mils wet) Theoretical Coverage - 457 ft²/US gal at 2 mils dft, allow appropriate loss factors Method of Application - Airless Spray, Brush, Conventional Spray, Roller Flash Point - Part A 93°F; Part B 120°F; Mixed 95°F Induction Period - Not required
As a cosmetic finish on above water areas. Suitable for use on topsides, external superstructure, external decks and
boottops.
For use at Newbuilding, Maintenance & Repair or On Board Maintenance.
Mixing: Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied.
(1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.
Thinner: Thinning is not normally required. Consult the local representative for advice during application in extreme
conditions. Do not thin more than allowed by local environmental legislation.
Airless Spray: Recommended
Tip Range 13-18 thou (0.33-0.45 mm)
Total output fluid pressure at spray tip not less than 2200 psi (155 kg/cm²)
Conventional Spray: Use suitable proprietary equipment. Thinning may be required.
Brush/Roller: Suitable
Cleaner: International GTA056/GTA713/GTA733
Work Stoppages and Cleanup: Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with
International GTA056/GTA713/GTA733. Once units of paint have been mixed they should not be resealed and it is
advised that after prolonged stoppages work recommences with freshly mixed units.
Clean all equipment immediately after use with International GTA056/GTA713/GTA733. It is good working practice
to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend
upon amount sprayed, temperature and elapsed time, including any delays. Do not exceed pot life limitations.
All surplus materials and empty containers should be disposed of in accordance with appropriate regional
regulations/legislation
Welding: In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be
emitted which will require the use of appropriate personal protective equipment and adequate local exhaust
ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 “Safety in Welding and
Cutting.”
Available upon request
All work involving the application and use of this product should be performed in compliance with all
relevant national Health, Safety & Environmental standards and regulations.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health
and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and
container labels. If you do not fully understand these warnings and instructions or if you can not strictly
comply with them, do not use this product. Proper ventilation and protective measures must be provided
during application and drying to keep solvent vapor concentrations within safe limits and to protect against
toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face
masks, barrier creams etc.) Actual safety measures are dependant on application methods and work
environment.
EMERGENCY CONTACT NUMBERS:
USA/Canada – Medical Advisory Number 1-800-854-6813
Europe – Contact (44) 191 4696111. For advice to Doctors & Hospitals only contact (44) 207 6359191
China – Contact (86) 532 83889090
R.O.W. – Contact Regional Office
Warning: Contains isocyanate. Wear air-fed hood for spray application.
Disclaimer: Color Matching and Prices of each product will be available upon request.