TEMPERATE
A hard wearing, surface tolerant, two pack epoxy primer. A low temperature version is available for use at
temperatures down to -5°C (see separate datasheet).
TEMPERATE A hard wearing, surface tolerant, two pack epoxy primer. A low temperature version is available for use at temperatures down to -5°C (see separate datasheet). Color - KHA300-Off White, KHA302-Grey, KHA303-Red, KHA304-Black, KHA305-Buff. These colours are suitable for immersion service. Special colours, which are not suitable for immersion service, can be matched to meet customer specifications. Finish/Sheen - Low-Gloss Part B (Curing Agent) - KHA062 Volume Solids - 73% ±2% (ISO 3233:1998) Mix Ratio - 4 volume(s) Part A to 1 volume(s) Part B Typical Film Thickness - 125 microns dry (171 microns wet) Theoretical Coverage - 5.84 m²/litre at 125 microns dft, allow appropriate loss factors Method of Application - Airless Spray, Brush, Conventional Spray, Roller Flash Point - Part A 44°C; Part B 40°C; Mixed 40°C Induction Period - 30 minutes at temperatures below 21°C
As an epoxy anticorrosive coating for use from Keel to Rail.
Suitable for use with controlled cathodic protection.
For use at Newbuilding, Maintenance & Repair or On Board Maintenance.
Application: Apply by conventional or airless spray. Application by other methods, brush or roller may require more than one
coat and is suggested for small areas only of stripe coating. Strain material through a minimum 60 mesh screen
before application. Apply at 160 microns wet which will yield 127 microns dry film thickness. Consult the following
equipment recommendations or utilize suitable equal.
Tinting: Range of colours available from Chromascan. Most colours require that containers be slightly short filled to
accommodate the addition of colourant. Actual coverage will depend upon amount of colourant added and should
be taken into consideration when ordering. A limited number of Intertuf 262 tinted colours may require more than
one coat for complete hiding
Mixing: Material is supplied in 2 containers as a unit. Always mix a complete unit in the proportions supplied. (1) Agitate
Part A with a power agitator, (2) Combine entire contents of Part A and B and mix thoroughly with the power
agitator, (3) Allow the coating a 30 minute sweat-in period, at temperatures below 21°C.
Thinner: Not recommended. Use International GTA220 only in exceptional circumstances. DO NOT thin more than allowed
by local environmental legislation.
Airless Spray: Minimum 30:1 ratio pump; 0.021″- 0.033″ (534-838 microns) orifice tip; 3/8″ (9.5 mm) ID high pressure material
hose; 60 mesh tip filter.
Conventional Spray: DeVilbiss MBC-510 gun E tip and 704 air cap; 3/8″ (9.5mm) ID material hose; double regulated pressure tank with oil and moisture separator.
Brush: Use appropriate size China bristle brush.
Roller: Use All Purpose Roller cover with 3/8″ (9.5mm) pile smooth to medium nap. Prewash roller cover to remove loose
fibers prior to use.
Cleaner: International GTA220/GTA822
Work Stoppages and Cleanup: Clean all equipment immediately after use with International GTA220/GTA822. Spray equipment requires flushing with this solvent. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency will depend upon factors such as amount sprayed, temperature and elapsed time including work stoppages. Monitor material condition. Do not exceed pot life limitations. All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.
Welding: In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be
emitted which will require the use of appropriate personal protective equipment and adequate local exhaust
ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 “Safety in Welding and
Cutting.”
Available upon request
All work involving the application and use of this product should be performed in compliance with all
relevant national Health, Safety & Environmental standards and regulations.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health
and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and
container labels. If you do not fully understand these warnings and instructions or if you can not strictly
comply with them, do not use this product. Proper ventilation and protective measures must be provided
during application and drying to keep solvent vapour concentrations within safe limits and to protect
against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves,
goggles, face masks, barrier creams etc.) Actual safety measures are dependent on application methods
and work environment.
EMERGENCY CONTACT NUMBERS:
USA/Canada – Medical Advisory Number 1-800-854-6813
Europe – Contact (44) 191 4696111. For advice to Doctors & Hospitals only contact (44) 207 6359191
R.O.W. – Contact Regional Office
SAFETY
Page 3 of 4
Ref:
Disclaimer: Color Matching and Prices of each product will be available upon request.