745 Aurora Blvd., Brgy. Mariana, New Manila, Quezon City

CALL US: 286-9799

Interzone 485

An ultra high build, high volume solids, two component catalysed epoxy, capable of being applied up to 3000
microns (120 mils) dry film thickness, and providing excellent impact resistance, abrasion resistance and
adhesion properties.
Suitable for Application using standard airless spray equipment, economical to apply.
Excellent resistance to alkalis, chemicals and petroleum products.

Interzone 485 Non Skid Deck Epoxy Coating

 

 

An ultra high build, high volume solids, two component catalysed epoxy, capable of being applied up to 3000 microns (120 mils) dry film thickness, and providing excellent impact resistance, abrasion resistance and adhesion properties. Suitable for Application using standard airless spray equipment, economical to apply. Excellent resistance to alkalis, chemicals and petroleum products.   Colour: Limited range Gloss Level: Semi Gloss Volume Solids: 99% Typical Thickness: 1000-3000 microns (40-120 mils) dry equivalent to || 1010-3030 microns (40.4-121.2 mils) wet Theoretical Coverage: 0.99 m²/litre at 1000 microns d.f.t and stated volume solids || 40 sq.ft/US gallon at 40 mils d.f.t and stated volume solids Practical Coverage: Allow appropriate loss factors Method of Application: Airless Spray

As a coating for the protection of steelwork in severe environments where high abrasion and corrosion
resistance are required including splashzone areas on offshore oil and gas platforms, wharf piles, ship loading
facilities, jetties, decks, bridges, chemical plants, pulp and paper mills, and water treatment plants.
Particularly suitable when used in conjunction with appropriate aggregate to provide a tough, durable non-slip
deck system. Interzone 485 is ideally suited for use on heliports, work areas and walkways on offshore
structures.
Excellent resistance to cathodic disbondment, gives good compatibility with both sacrificial anode and
impressed current systems. Interzone 485 is particularly suitable for the long term protection of sub-sea
structures, or as a shop or field applied coating for hot, cathodically protected oil or gas pipelines.
As a tank lining for abrasive slurry e.g. CIL/CIP tanks in the gold mining industry

Mixing: Material is supplied in two containers as a unit. Always mix a complete unit
in the proportions supplied. Once the unit has been mixed it must be used
within the working pot life specified.
(1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base
(Part A) and mix thoroughly with power agitator.

Mix Ratio: 4 part(s) : 1 part(s) by volume

Working Pot Life: 10°C (50°F) 15°C (59°F) 25°C (77°F) 40°C (104°F)
1 hour             1 hour         45 minutes     30 minutes
Airless Spray: Recommended – Tip Size 0.76 mm (30 thou) Total output fluid pressure at spray tip not less than 282 kg/cm² (4010 p.s.i.)

Air Spray (Pressure Pot): Not suitable

Brush: Suitable – For areas less than 0.1m2 brush application is possible. Multiple coats and thinning up to 3% maybe required.

Roller: International GTA203 (Thin up to 3%) – Do not thin more than allowed by local environmental legislation

Cleaner: International GTA853 or International GTA203 Work Stoppages: Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with International GTA853 (or GTA203). Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units.

Clean Up: Clean all equipment immediately after use with International GTA853 (or GTA203). It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays.

All surplus materials and empty containers should be disposed of in
accordance with appropriate regional regulations/legislation.

Available upon request

This product is intended for use only by professional applicators in industrial situations in accordance with the advice given on this sheet, the Material Safety Data Sheet and the container(s), and should not be used without reference to the Material Safety Data Sheet (MSDS) which International Protective Coatings has provided to its customers. All work involving the application and use of this product should be performed in compliance with allrelevant national, Health, Safety & Environmental standards and regulations.
In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation.
If in doubt regarding the suitability of use of this product, consult International Protective Coatings for further advice.

Disclaimer: Color Matching and Prices of each product will be available upon request.